LIVIVO - Search results -

Search results

Result 1 - 10 of total 13

Search options

Article ; Online: An Assessment of Sikh Turban's Head Protection in Bicycle Incident Scenarios.

Yu, Xiancheng / Singh, Gurpreet / Kaur, Amritvir / Ghajari, Mazdak

2024 Volume 52, Issue 4, Page(s) 946–957

Abstract: Due to religious tenets, Sikh population wear turbans and are exempted from wearing helmets in several countries. However, the extent of protection provided by turbans against head injuries during head impacts remains untested. One aim of this study was ... ...

Abstract	Due to religious tenets, Sikh population wear turbans and are exempted from wearing helmets in several countries. However, the extent of protection provided by turbans against head injuries during head impacts remains untested. One aim of this study was to provide the first-series data of turbans' protective performance under impact conditions that are representative of real-world bicycle incidents and compare it with the performance of bicycle helmets. Another aim was to suggest potential ways for improving turban's protective performance. We tested five different turbans, distinguished by two wrapping styles and two fabric materials with a size variation in one of the styles. A Hybrid III headform fitted with the turban was dropped onto a 45 degrees anvil at 6.3 m/s and head accelerations were measured. We found large difference in the performance of different turbans, with up to 59% difference in peak translational acceleration, 85% in peak rotational acceleration, and 45% in peak rotational velocity between the best and worst performing turbans. For the same turban, impact on the left and right sides of the head produced very different head kinematics, showing the effects of turban layering. Compared to unprotected head impacts, turbans considerably reduce head injury metrics. However, turbans produced higher values of peak linear and rotational accelerations in front and left impacts than bicycle helmets, except from one turban which produced lower peak head kinematics values in left impacts. In addition, turbans produced peak rotational velocities comparable with bicycle helmets, except from one turban which produced higher values. The impact locations tested here were covered with thick layers of turbans and they were impacted against flat anvils. Turbans may not provide much protection if impacts occur at regions covered with limited amount of fabric or if the impact is against non-flat anvils, which remain untested. Our analysis shows that turbans can be easily compressed and bottom out creating spikes in the headform's translational acceleration. In addition, the high friction between the turban and anvil surface leads to higher tangential force generating more rotational motion. Hence, in addition to improving the coverage of the head, particularly in the crown and rear locations, we propose two directions for turban improvement: (i) adding deformable materials within the turban layers to increase the impact duration and reduce the risk of bottoming out; (ii) reducing the friction between turban layers to reduce the transmission of rotational motion to the head. Overall, the study assessed Turbans' protection in cyclist head collisions, with a vision that the results of this study can guide further necessary improvements for advanced head protection for the Sikh community.
MeSH term(s)	Humans ; Bicycling/injuries ; Craniocerebral Trauma/prevention & control ; Mechanical Phenomena ; Biomechanical Phenomena ; Acceleration ; Head Protective Devices ; Head
Language	English
Publishing date	2024-02-02
Publishing country	United States
Document type	Journal Article
ZDB-ID	185984-5
ISSN	1573-9686 ; 0191-5649 ; 0090-6964
ISSN (online)	1573-9686
ISSN	0191-5649 ; 0090-6964
DOI	10.1007/s10439-023-03431-7
Database	MEDical Literature Analysis and Retrieval System OnLINE

In stock of ZB MED Cologne/Königswinter

Zs.A 1018: Show issues

Location:
Je nach Verfügbarkeit (siehe Angabe bei Bestand)
bis Jg. 1994: Bestellungen von Artikeln über das Online-Bestellformular
Jg. 1995 - 2021: Lesesall (1.OG)
ab Jg. 2022: Lesesaal (EG)

Order via subito

This service is chargeable due to the Delivery terms set by subito. Orders including an article and supplementary material will be classified as separate orders. In these cases, fees will be demanded for each order.

Details ▾
- See ZB MED holdings
- Order with fees

Article ; Online: Protective Performance of Helmets and Goggles in Mitigating Brain Biomechanical Response to Primary Blast Exposure.

Yu, Xiancheng / Ghajari, Mazdak

Annals of biomedical engineering

2022 Volume 50, Issue 11, Page(s) 1579–1595

Abstract: The current combat helmets are primarily designed to mitigate blunt impacts and ballistic loadings. Their protection against primary blast wave is not well studied. In this paper, we comprehensively assessed the protective capabilities of the advanced ... ...

Abstract	The current combat helmets are primarily designed to mitigate blunt impacts and ballistic loadings. Their protection against primary blast wave is not well studied. In this paper, we comprehensively assessed the protective capabilities of the advanced combat helmet and goggles against blast waves with different intensity and directions. Using a high-fidelity human head model, we compared the intracranial pressure (ICP), cerebrospinal fluid (CSF) cavitation, and brain strain and strain rate predicted from bare head, helmet-head and helmet-goggles-head simulations. The helmet was found to be effective in mitigating the positive ICP (24-57%) and strain rate (5-34%) in all blast scenarios. Goggles were found to be effective in mitigating the positive ICP in frontal (6-16%) and lateral (5-7%) blast exposures. However, the helmet and goggles had minimal effects on mitigating CSF cavitation and even increased brain strain. Further investigation showed that wearing a helmet leads to higher risk of cavitation. In addition, their presence increased the head kinetic energy, leading to larger strains in the brain. Our findings can improve our understanding of the protective effects of helmets and goggles and guide the design of helmet pads to mitigate brain responses to blast.
MeSH term(s)	Humans ; Head Protective Devices ; Eye Protective Devices ; Blast Injuries/prevention & control ; Computer Simulation ; Biomechanical Phenomena ; Brain/physiology
Language	English
Publishing date	2022-03-16
Publishing country	United States
Document type	Journal Article
ZDB-ID	185984-5
ISSN	1573-9686 ; 0191-5649 ; 0090-6964
ISSN (online)	1573-9686
ISSN	0191-5649 ; 0090-6964
DOI	10.1007/s10439-022-02936-x
Database	MEDical Literature Analysis and Retrieval System OnLINE

In stock of ZB MED Cologne/Königswinter

Zs.A 1018: Show issues

Location:
Je nach Verfügbarkeit (siehe Angabe bei Bestand)
bis Jg. 1994: Bestellungen von Artikeln über das Online-Bestellformular
Jg. 1995 - 2021: Lesesall (1.OG)
ab Jg. 2022: Lesesaal (EG)

Order via subito

Details ▾
- See ZB MED holdings
- Order with fees

Article ; Online: Head Impact Location, Speed and Angle from Falls and Trips in the Workplace.

Yu, Xiancheng / Baker, Claire E / Ghajari, Mazdak

Annals of biomedical engineering

2023

Abstract: Traumatic brain injury (TBI) is a common injury in the workplace. Trips and falls are the leading causes of TBI in the workplace. However, industrial safety helmets are not designed for protecting the head under these impact conditions. Instead, they are ...

Abstract	Traumatic brain injury (TBI) is a common injury in the workplace. Trips and falls are the leading causes of TBI in the workplace. However, industrial safety helmets are not designed for protecting the head under these impact conditions. Instead, they are designed to pass the regulatory standards which test head protection against falling heavy and sharp objects. This is likely to be due to the limited understanding of head impact conditions from trips and falls in workplace. In this study, we used validated human multi-body models to predict the head impact location, speed and angle (measured from the ground) during trips, forward falls and backward falls. We studied the effects of worker size, initial posture, walking speed, width and height of the tripping barrier, bracing and falling height on the head impact conditions. Overall, we performed 1692 simulations. The head impact speed was over two folds larger in falls than trips, with backward falls producing highest impact speeds. However, the trips produced impacts with smaller impact angles to the ground. Increasing the walking speed increased the head impact speed but bracing reduced it. We found that 41% of backward falls and 19% of trips/forward falls produced head impacts located outside the region of helmet coverage. Next, we grouped all the data into three sub-groups based on the head impact angle: [0°, 30°], (30°, 60°] and (60°, 90°] and excluded groups with small number of cases. We found that most trips and forward falls lead to impact angles within the (30°, 60°] and (60°, 90°] groups while all backward falls produced impact angles within (60°, 90°] group. We therefore determined five representative head impact conditions from these groups by selecting the 75th percentile speed, mean value of angle intervals and median impact location (determined by elevation and azimuth angles) of each group. This led to two representative head impact conditions for trips: 2.7 m/s at 45° and 3.9 m/s at 75°, two for forward falls: 3.8 m/s at 45° and 5.5 m/s at 75° and one for backward falls: 9.4 m/s at 75°. These impact conditions can be used to improve industrial helmet standards.
Language	English
Publishing date	2023-02-06
Publishing country	United States
Document type	Journal Article
ZDB-ID	185984-5
ISSN	1573-9686 ; 0191-5649 ; 0090-6964
ISSN (online)	1573-9686
ISSN	0191-5649 ; 0090-6964
DOI	10.1007/s10439-023-03146-9
Database	MEDical Literature Analysis and Retrieval System OnLINE

In stock of ZB MED Cologne/Königswinter

Zs.A 1018: Show issues

Location:
Je nach Verfügbarkeit (siehe Angabe bei Bestand)
bis Jg. 1994: Bestellungen von Artikeln über das Online-Bestellformular
Jg. 1995 - 2021: Lesesall (1.OG)
ab Jg. 2022: Lesesaal (EG)

Order via subito

Details ▾
- See ZB MED holdings
- Order with fees

Article ; Online: A Review of Cyclist Head Injury, Impact Characteristics and the Implications for Helmet Assessment Methods.

Baker, Claire E / Yu, Xiancheng / Patel, Saian / Ghajari, Mazdak

Annals of biomedical engineering

2023 Volume 51, Issue 5, Page(s) 875–904

Abstract: Head injuries are common for cyclists involved in collisions. Such collision scenarios result in a range of injuries, with different head impact speeds, angles, locations, or surfaces. A clear understanding of these collision characteristics is vital to ... ...

Abstract	Head injuries are common for cyclists involved in collisions. Such collision scenarios result in a range of injuries, with different head impact speeds, angles, locations, or surfaces. A clear understanding of these collision characteristics is vital to design high fidelity test methods for evaluating the performance of helmets. We review literature detailing real-world cyclist collision scenarios and report on these key characteristics. Our review shows that helmeted cyclists have a considerable reduction in skull fracture and focal brain pathologies compared to non-helmeted cyclists, as well as a reduction in all brain pathologies. The considerable reduction in focal head pathologies is likely to be due to helmet standards mandating thresholds of linear acceleration. The less considerable reduction in diffuse brain injuries is likely to be due to the lack of monitoring head rotation in test methods. We performed a novel meta-analysis of the location of 1809 head impacts from ten studies. Most studies showed that the side and front regions are frequently impacted, with one large, contemporary study highlighting a high proportion of occipital impacts. Helmets frequently had impact locations low down near the rim line. The face is not well protected by most conventional bicycle helmets. Several papers determine head impact speed and angle from in-depth reconstructions and computer simulations. They report head impact speeds from 5 to 16 m/s, with a concentration around 5 to 8 m/s and higher speeds when there was another vehicle involved in the collision. Reported angles range from 10° to 80° to the normal, and are concentrated around 30°-50°. Our review also shows that in nearly 80% of the cases, the head impact is reported to be against a flat surface. This review highlights current gaps in data, and calls for more research and data to better inform improvements in testing methods of standards and rating schemes and raise helmet safety.
MeSH term(s)	Humans ; Bicycling/injuries ; Craniocerebral Trauma/prevention & control ; Computer Simulation ; Head Protective Devices ; Acceleration ; Accidents, Traffic
Language	English
Publishing date	2023-03-14
Publishing country	United States
Document type	Meta-Analysis ; Journal Article ; Review
ZDB-ID	185984-5
ISSN	1573-9686 ; 0191-5649 ; 0090-6964
ISSN (online)	1573-9686
ISSN	0191-5649 ; 0090-6964
DOI	10.1007/s10439-023-03148-7
Database	MEDical Literature Analysis and Retrieval System OnLINE

In stock of ZB MED Cologne/Königswinter

Zs.A 1018: Show issues

Location:
Je nach Verfügbarkeit (siehe Angabe bei Bestand)
bis Jg. 1994: Bestellungen von Artikeln über das Online-Bestellformular
Jg. 1995 - 2021: Lesesall (1.OG)
ab Jg. 2022: Lesesaal (EG)

Order via subito

Details ▾
- See ZB MED holdings
- Order with fees

Article: In-Depth Bicycle Collision Reconstruction: From a Crash Helmet to Brain Injury Evaluation.

Yu, Xiancheng / Baker, Claire E / Brown, Mike / Ghajari, Mazdak

Bioengineering (Basel, Switzerland)

2023 Volume 10, Issue 3

Abstract: Traumatic brain injury (TBI) is a prevalent injury among cyclists experiencing head collisions. In legal cases, reliable brain injury evaluation can be difficult and controversial as mild injuries cannot be diagnosed with conventional brain imaging ... ...

Abstract	Traumatic brain injury (TBI) is a prevalent injury among cyclists experiencing head collisions. In legal cases, reliable brain injury evaluation can be difficult and controversial as mild injuries cannot be diagnosed with conventional brain imaging methods. In such cases, accident reconstruction may be used to predict the risk of TBI. However, lack of collision details can render accident reconstruction nearly impossible. Here, we introduce a reconstruction method to evaluate the brain injury in a bicycle-vehicle collision using the crash helmet alone. Following a thorough inspection of the cyclist's helmet, we identified a severe impact, a moderate impact and several scrapes, which helped us to determine the impact conditions. We used our helmet test rig and intact helmets identical to the cyclist's helmet to replicate the damage seen on the cyclist's helmet involved in the real-world collision. We performed both linear and oblique impacts, measured the translational and rotational kinematics of the head and predicted the strain and the strain rate across the brain using a computational head model. Our results proved the hypothesis that the cyclist sustained a severe impact followed by a moderate impact on the road surface. The estimated head accelerations and velocity (167 g, 40.7 rad/s and 13.2 krad/s
Language	English
Publishing date	2023-03-02
Publishing country	Switzerland
Document type	Journal Article
ZDB-ID	2746191-9
ISSN	2306-5354
ISSN	2306-5354
DOI	10.3390/bioengineering10030317
Database	MEDical Literature Analysis and Retrieval System OnLINE

Order via subito

Article: Oblique impact responses of Hybrid III and a new headform with more biofidelic coefficient of friction and moments of inertia.

Yu, Xiancheng / Halldin, Peter / Ghajari, Mazdak

Frontiers in bioengineering and biotechnology

2022 Volume 10, Page(s) 860435

Abstract: New oblique impact methods for evaluating head injury mitigation effects of helmets are emerging, which mandate measuring both translational and rotational kinematics of the headform. These methods need headforms with biofidelic mass, moments of inertia ( ...

Abstract	New oblique impact methods for evaluating head injury mitigation effects of helmets are emerging, which mandate measuring both translational and rotational kinematics of the headform. These methods need headforms with biofidelic mass, moments of inertia (MoIs), and coefficient of friction (CoF). To fulfill this need, working group 11 of the European standardization head protection committee (CEN/TC158) has been working on the development of a new headform with realistic MoIs and CoF, based on recent biomechanics research on the human head. In this study, we used a version of this headform (Cellbond) to test a motorcycle helmet under the oblique impact at 8 m/s at five different locations. We also used the Hybrid III headform, which is commonly used in the helmet oblique impact. We tested whether there is a difference between the predictions of the headforms in terms of injury metrics based on head kinematics, including peak translational and rotational acceleration, peak rotational velocity, and BrIC (brain injury criterion). We also used the Imperial College finite element model of the human head to predict the strain and strain rate across the brain and tested whether there is a difference between the headforms in terms of the predicted strain and strain rate. We found that the Cellbond headform produced similar or higher peak translational accelerations depending on the impact location (-3.2% in the front-side impact to 24.3% in the rear impact). The Cellbond headform, however, produced significantly lower peak rotational acceleration (-41.8% in a rear impact to -62.7% in a side impact), peak rotational velocity (-29.5% in a side impact to -47.6% in a rear impact), and BrIC (-29% in a rear-side impact to -45.3% in a rear impact). The 90th percentile values of the maximum brain strain and strain rate were also significantly lower using this headform. Our results suggest that MoIs and CoF have significant effects on headform rotational kinematics, and consequently brain deformation, during the helmeted oblique impact. Future helmet standards and rating methods should use headforms with realistic MoIs and CoF (e.g., the Cellbond headform) to ensure more accurate representation of the head in laboratory impact tests.
Language	English
Publishing date	2022-09-08
Publishing country	Switzerland
Document type	Journal Article
ZDB-ID	2719493-0
ISSN	2296-4185
ISSN	2296-4185
DOI	10.3389/fbioe.2022.860435
Database	MEDical Literature Analysis and Retrieval System OnLINE

Order via subito

Article: Non-Lethal Blasts can Generate Cavitation in Cerebrospinal Fluid While Severe Helmeted Impacts Cannot: A Novel Mechanism for Blast Brain Injury.

Yu, Xiancheng / Nguyen, Thuy-Tien / Wu, Tianchi / Ghajari, Mazdak

Frontiers in bioengineering and biotechnology

2022 Volume 10, Page(s) 808113

Abstract: Cerebrospinal fluid (CSF) cavitation is a likely physical mechanism for producing traumatic brain injury (TBI) under mechanical loading. In this study, we investigated CSF cavitation under blasts and helmeted impacts which represented loadings in ... ...

Abstract	Cerebrospinal fluid (CSF) cavitation is a likely physical mechanism for producing traumatic brain injury (TBI) under mechanical loading. In this study, we investigated CSF cavitation under blasts and helmeted impacts which represented loadings in battlefield and road traffic/sports collisions. We first predicted the human head response under the blasts and impacts using computational modelling and found that the blasts can produce much lower negative pressure at the contrecoup CSF region than the impacts. Further analysis showed that the pressure waves transmitting through the skull and soft tissue are responsible for producing the negative pressure at the contrecoup region. Based on this mechanism, we hypothesised that blast, and not impact, can produce CSF cavitation. To test this hypothesis, we developed a one-dimensional simplified surrogate model of the head and exposed it to both blasts and impacts. The test results confirmed the hypothesis and computational modelling of the tests validated the proposed mechanism. These findings have important implications for prevention and diagnosis of blast TBI.
Language	English
Publishing date	2022-07-07
Publishing country	Switzerland
Document type	Journal Article
ZDB-ID	2719493-0
ISSN	2296-4185
ISSN	2296-4185
DOI	10.3389/fbioe.2022.808113
Database	MEDical Literature Analysis and Retrieval System OnLINE

Order via subito

Article ; Online: An assessment of blast modelling techniques for injury biomechanics research.

Yu, Xiancheng / Ghajari, Mazdak

International journal for numerical methods in biomedical engineering

2019 Volume 35, Issue 12, Page(s) e3258

Abstract: Blast-induced traumatic brain injury (TBI) has been affecting combatants and civilians. The blast pressure wave is thought to have a significant contribution to blast-related TBI. Due to the limitations and difficulties of conducting blast tests on ... ...

Abstract	Blast-induced traumatic brain injury (TBI) has been affecting combatants and civilians. The blast pressure wave is thought to have a significant contribution to blast-related TBI. Due to the limitations and difficulties of conducting blast tests on surrogates, computational modelling has been used as a key method for exploring this field. However, the blast wave modelling methods reported in current literature have drawbacks. They either cannot generate the desirable blast pressure wave history or they are unable to accurately simulate the blast wave/structure interaction. In addition, boundary conditions, which can have significant effects on model predictions, have not been described adequately. Here, we critically assess the commonly used methods for simulating blast wave propagation in air (open-field blast) and its interaction with the human body. We investigate the predicted blast wave time history, blast wave transmission, and the effects of various boundary conditions in three-dimensional (3D) models of blast prediction. We propose a suitable meshing topology, which enables accurate prediction of blast wave propagation and interaction with the human head and significantly decreases the computational cost in 3D simulations. Finally, we predict strain and strain rate in the human brain during blast wave exposure and show the influence of the blast wave modelling methods on the brain response. The findings presented here can serve as guidelines for accurately modelling blast wave generation and interaction with the human body for injury biomechanics studies and design of prevention systems.
MeSH term(s)	Blast Injuries/pathology ; Brain Injuries, Traumatic/pathology ; Computer Simulation ; Explosions ; Finite Element Analysis ; Head/physiology ; Humans ; Models, Biological ; Pressure
Language	English
Publishing date	2019-10-20
Publishing country	England
Document type	Journal Article ; Research Support, Non-U.S. Gov't
ZDB-ID	2540968-2
ISSN	2040-7947 ; 2040-7939
ISSN (online)	2040-7947
ISSN	2040-7939
DOI	10.1002/cnm.3258
Database	MEDical Literature Analysis and Retrieval System OnLINE

Full text online

Accessible to users with ZB MED library card

Order via subito

Details ▾
- Full text online
- Order with fees

Article ; Online: The Protective Performance of Modern Motorcycle Helmets Under Oblique Impacts.

Yu, Xiancheng / Logan, Ingrid / de Pedro Sarasola, Itziar / Dasaratha, Atulit / Ghajari, Mazdak

Annals of biomedical engineering

2022 Volume 50, Issue 11, Page(s) 1674–1688

Abstract: Motorcyclists are at high risk of head injuries, including skull fractures, focal brain injuries, intracranial bleeding and diffuse brain injuries. New helmet technologies have been developed to mitigate head injuries in motorcycle collisions, but there ... ...

Abstract	Motorcyclists are at high risk of head injuries, including skull fractures, focal brain injuries, intracranial bleeding and diffuse brain injuries. New helmet technologies have been developed to mitigate head injuries in motorcycle collisions, but there is limited information on their performance under commonly occurring oblique impacts. We used an oblique impact method to assess the performance of seven modern motorcycle helmets at five impact locations. Four helmets were fitted with rotational management technologies: a low friction layer (MIPS), three-layer liner system (Flex) and dampers-connected liner system (ODS). Helmets were dropped onto a 45° anvil at 8 m/s at five locations. We determined peak translational and rotational accelerations (PTA and PRA), peak rotational velocity (PRV) and brain injury criteria (BrIC). In addition, we used a human head finite element model to predict strain distribution across the brain and in corpus callosum and sulci. We found that the impact location affected the injury metrics and brain strain, but this effect was not consistent. The rear impact produced lowest PTAs but highest PRAs. This impact produced highest strain in corpus callosum. The front impact produced the highest PRV and BrIC. The side impact produced the lowest PRV, BrIC and strain across the brain, sulci and corpus callosum. Among helmet technologies, MIPS reduced all injury metrics and brain strain compared with conventional helmets. Flex however was effective in reducing PRA only and ODS was not effective in reducing any injury metrics in comparison with conventional helmets. This study shows the importance of using different impact locations and injury metrics when assessing head protection effects of helmets. It also provides new data on the performance of modern motorcycle helmets. These results can help with improving helmet design and standard and rating test methods.
MeSH term(s)	Humans ; Head Protective Devices ; Motorcycles ; Craniocerebral Trauma/prevention & control ; Acceleration ; Head ; Brain Injuries
Language	English
Publishing date	2022-04-13
Publishing country	United States
Document type	Journal Article
ZDB-ID	185984-5
ISSN	1573-9686 ; 0191-5649 ; 0090-6964
ISSN (online)	1573-9686
ISSN	0191-5649 ; 0090-6964
DOI	10.1007/s10439-022-02963-8
Database	MEDical Literature Analysis and Retrieval System OnLINE

In stock of ZB MED Cologne/Königswinter

Zs.A 1018: Show issues

Location:
Je nach Verfügbarkeit (siehe Angabe bei Bestand)
bis Jg. 1994: Bestellungen von Artikeln über das Online-Bestellformular
Jg. 1995 - 2021: Lesesall (1.OG)
ab Jg. 2022: Lesesaal (EG)

Order via subito

Details ▾
- See ZB MED holdings
- Order with fees

Article: Development of a rodent high-energy blast injury model for investigating conditions associated with traumatic amputations.

Kazezian, Zepur / Yu, Xiancheng / Ramette, Martin / Macdonald, Warren / Bull, Anthony M J

Bone & joint research

2021 Volume 10, Issue 3, Page(s) 166–172

Abstract: Aims: In recent conflicts, most injuries to the limbs are due to blasts resulting in a large number of lower limb amputations. These lead to heterotopic ossification (HO), phantom limb pain (PLP), and functional deficit. The mechanism of blast loading ... ...

Abstract	Aims: In recent conflicts, most injuries to the limbs are due to blasts resulting in a large number of lower limb amputations. These lead to heterotopic ossification (HO), phantom limb pain (PLP), and functional deficit. The mechanism of blast loading produces a combined fracture and amputation. Therefore, to study these conditions, in vivo models that replicate this combined effect are required. The aim of this study is to develop a preclinical model of blast-induced lower limb amputation. Methods: Cadaveric Sprague-Dawley rats' left hindlimbs were exposed to blast waves of 7 to 13 bar burst pressures and 7.76 ms to 12.68 ms positive duration using a shock tube. Radiographs and dissection were used to identify the injuries. Results: Higher burst pressures of 13 and 12 bar caused multiple fractures at the hip, and the right and left limbs. Lowering the pressure to 10 bar eliminated hip fractures; however, the remaining fractures were not isolated to the left limb. Further reducing the pressure to 9 bar resulted in the desired isolated fracture of the left tibia with a dramatic reduction in the fractures to other sites. Conclusion: In this paper, a rodent blast injury model has been developed in the hindlimb of cadaveric rats that combines the blast and fracture in one insult, necessitating amputation. Experimental setup with 9 bar burst pressure and 9.13 ms positive duration created a fracture at the tibia with total reduction in non-targeted fractures, rendering 9 bar burst pressure suitable for translation to a survivable model to investigate blast injury-associated diseases. Cite this article:
Language	English
Publishing date	2021-03-02
Publishing country	England
Document type	Journal Article
ZDB-ID	2669244-2
ISSN	2046-3758
ISSN	2046-3758
DOI	10.1302/2046-3758.103.BJR-2020-0367.R1
Database	MEDical Literature Analysis and Retrieval System OnLINE

Order via subito

To top

More links

Kategorien

In stock of ZB MED Cologne/Königswinter

Order via subito

More links

Kategorien

In stock of ZB MED Cologne/Königswinter

Order via subito

More links

Kategorien

In stock of ZB MED Cologne/Königswinter

Order via subito

More links

Kategorien

In stock of ZB MED Cologne/Königswinter

Order via subito

More links

Kategorien

Order via subito

More links

Kategorien

Order via subito

More links

Kategorien

Order via subito

Full text online

More links

Kategorien

Order via subito

More links

Kategorien

In stock of ZB MED Cologne/Königswinter

Order via subito

More links

Kategorien

Order via subito