Artikel ; Online: A comparative study of the cutting efficiency of diamond rotary instruments with different grit sizes with a low-speed electric handpiece against zirconia specimens.
The Journal of prosthetic dentistry
2023 Band 131, Heft 1, Seite(n) 101.e1–101.e8
Abstract: Statement of problem: The use of zirconia in dentistry has increased. However, little attention has been given to the difficulty experienced by clinicians when cutting zirconia restorations intraorally. Evidence for which grit size and type of rotary ... ...
| Abstract | Statement of problem: The use of zirconia in dentistry has increased. However, little attention has been given to the difficulty experienced by clinicians when cutting zirconia restorations intraorally. Evidence for which grit size and type of rotary instrument is best for cutting zirconia intraorally is lacking. Purpose: The purpose of this in vitro study was to identify the most efficient diamond rotary instrument grit size for cutting zirconia intraorally. Material and methods: Efficiency was measured by comparing the cutting depth of each rotary instrument into zirconia, analyzing zirconia specimens for surface damage after cutting, and measuring instrument deterioration. Thirty zirconia specimens of the same measurements were used as test specimens and cut with 30 diamond rotary instruments with different grit sizes. An electric handpiece was used with constant force (1.7 N), speed (40 000 rpm), time (1 min), and water flow rate (25 mL/min) to produce comparative data. The mean cutting efficiency values were compared by analysis, and the median values were compared by the nonparametric Kruskal-Wallis test (α=.05). Each test was followed up with pair wise comparisons of the mean or median values if significance was indicated. Results: The greatest cutting depth was achieved with a fine-grit instrument with a mean cutting depth of 5.79 mm compared with 4.54 mm for the coarse-grit instrument (P=.032). The greatest damage to zirconia was done by the coarse- and supercoarse-grit instruments (both 33%), with no substrate damage by the superfine-, fine-, and medium-grit instruments. The greatest instrument deterioration was found on the supercoarse rotary instruments (9.05%). With only 3 exceptions, the power calculations were all sufficient and above 83%. Conclusions: The fine grit rotary instrument (between 40 and 50 µm) was the most efficient, achieving the greatest cutting depth, with no detectable macroscopic damage to the zirconia and minimal instrument deterioration. |
|---|---|
| Mesh-Begriff(e) | Diamond ; Zirconium ; Surface Properties ; Materials Testing |
| Chemische Substanzen | zirconium oxide (S38N85C5G0) ; Diamond (7782-40-3) ; Zirconium (C6V6S92N3C) |
| Sprache | Englisch |
| Erscheinungsdatum | 2023-11-03 |
| Erscheinungsland | United States |
| Dokumenttyp | Journal Article |
| ZDB-ID | 218157-5 |
| ISSN | 1097-6841 ; 0022-3913 |
| ISSN (online) | 1097-6841 |
| ISSN | 0022-3913 |
| DOI | 10.1016/j.prosdent.2023.10.004 |
| Datenquelle | MEDical Literature Analysis and Retrieval System OnLINE |
Volltext online
Zusatzmaterialien
Kategorien
Verfügbar in ZB MED Köln/Königswinter
| Ul III Zs.145: Hefte anzeigen | Standort: Je nach Verfügbarkeit (siehe Angabe bei Bestand) bis Jg. 2021: Bestellungen von Artikeln über das Online-Bestellformular ab Jg. 2022: Lesesaal (EG) |
Über subito bestellen
Dieser Service ist kostenpflichtig (siehe Lieferbedingungen von subito). Bestellungen, die einen Artikel nebst Supplementary Material umfassen, werden grundsätzlich wie mehrfache Bestellungen bearbeitet. Gebühren fallen in diesen Fällen für jede einzelne Bestellung an.